The robotic experiments are based on angular momentum. Inside of the cube there are center mounted motors which each spin a wheel. Three of these are mounted perpendicular to each other to give the cube the ability to change its position along any axis. This is best shown by the first...
The cheap software defined radio platforms that can be built out of a USB TV tuner aren’t getting much love on the Hackaday tip line of late. Thankfully, [Adam] sent in a great guide to cracking sub-GHz wireless protocols wide open , and ringing doorbells, opening cars, and potentiall...
Sometimes a pair of extremely similar builds hit the Hackaday tip line within hours of each other. We’re not one to play favorites, so here’s two projects that put RGB LED strips in a desk and workbench. [Charles] over at The Makers Workbench has long needed a lighting solution for hi...
No, it’s exactly opposite. The rolling shutter CMOS would ruin the illusion by capturing parts of the frame at a different time, whereas CCD captures the whole frame at a single point of the oscillation and that’s what makes the water appear stationary. I was just about to comment tha...
The Raspberry Pi has been very popular as a streaming music player. Sure, the only audio out option on the board is an analog stereo jack, but you can use a USB audio device to improve upon that if you wish. [Wouter van Wijk] wanted to use his RPi as a Spotify server. It’s a bit trick...
The idea for the project started off rather simple, but quickly got out of hand (check out the build log for full details on that). He thought it would be nice to have a backlight for the original screen. After mixed results he scrapped the original mainboard and started anew with som...
The DIP chip seen with most of its legs bent backwards is the ATtiny25 which makes the system work. It’s patched into the traces for the battery connections, button (on the other side of the board) and the IR LED he’s pinching with his left hand. Point it at a Cannon camera and push t...
The base for the add-on hardware is a chunk of protoboard the same size as the Pi itself. This is just slightly wider than the LCD screen, leaving room along the top for the row of buttons with different colors of LEDs in between them. Look closely in that nest of point-to-point wirin...
[Lindarose92] fabricated the shade out of narrow strips of corrugated cardboard. This particular lamp also has a cardboard base but we’re sure you could use it for just about any light source with doesn’t generate enough heat to cause problems. The build starts out with the tedious pr...
The device that these seamen are standing around is a US Navy targeting computer. It doesn’t use electricity, but relies on mechanical computing to adjust trajectories of the ship’s guns . Setting up to twenty-five different attributes by turning cranks and other input mechanisms lets...
More than ever, 3D printers are being used for small prototype and production runs, and the normal way of using a 3D printer with a single desktop app is becoming more and more out of date. [Zach 'Hoeken' Smith] has a solution to the frustration of printing out multiples of objects: i...
We think the pair of cylinders sticking up through the top of this project enclosure will be recognized by most readers as the business end of an ultrasonic rangefinder. This is the only control interface which [Thomas] chose to use. Although he didn’t write very extensively about the...
He’s using a Moteino, which is an Arduino clone of his own making. It’s tiny and features an RF module on the underside of the board which takes care of communicating with a base station inside the house. The module seen above rolls the microcontroller board up along with a 9V battery...
He doesn’t have a blog post about the project, but you can find a couple of images and his build instructions after the break. The firearm has a motor attached to the trigger that allows it to be fired by tapping into one of the extra channels on the RC car’s PCB. But you won’t just b...
Here’s a project inspired by a highly polished art piece. [Tobias] has been working on his own RGB LED clock which uses one light for each minute in an hour . He was inspired to start the project after seeing the Equinox clock . That one used a little PCB for each LED, and included an...
@aliveoneee: Even if wood is a little less efficient in terms of CO2 per kWh, it is better in the carbon scheme of things, because of where the carbon *came from*. Burning wood to produce energy is carbon neutral, because the carbon in wood came from the atmosphere to begin with, thro...
To our eye the NES looks completely unmodified when the case is closed. The cartridge slot still accepts games, but you don’t have to lower the frame into place once that cartridge has been inserted. The image above shows a ribbon cable connecting the top and bottom halves of the buil...
[Vasilis] works at CERN, and like any large organization that invented the World Wide Web, they take computer security pretty seriously. One ‘feature’ the IT staff implemented is locking the desktop whenever the screen saver runs. When [Vasilis] is in his office but not at his battles...
The actuators he’s using are too slow and rounding off the corners. Looks like he’s gotten much farther than the two previous attempts at a LASER MAME. One important bit is correcting for distortion caused by projecting onto a flat surface. The old vector monitors avoided it by using ...
[Hank Drum], as explained here , is a steel drum-type instrument made out of a propane tank. The name comes from the [Hang] or [Hang Drum] which is significantly more expensive than that $40 or so an empty propane tank costs. Of course, you’ll have to do some work to get it to play be...
For the last time, you cannot create an entire firearm with a 3D printer! You still need to use a steel barrel, bolt assembly, and other related parts. Meanwhile, I see there is a “we want freedom but will only snark on the internet for it” crowd, and then there are the gun owners. He...
![“Hacking the Xbox” Released for Free in Honor of [Aaron Swartz]](http://static.openruby.com/assets/pages/78/1b/781bb425a3f1b4dced49e65cf47f4101_100.jpg)
[Bunnie], the hardware hacker who first hacked into the original Xbox while at MIT, is releasing his book on the subject for free. The book was originally released in 2003, and delves into both the technical and legal aspects of hacking into the console. The book is being released alo...
[Tom] didn’t need a buck-converter. Just remove the shunt resistor from the meter (you can even see it in the photo) to drop the range. Should give you something that works well (and very easily) with a transistor driver and 3 – 5V. Also, [Tom] should do some more research on VU meter...
When you’re getting close to a production run the prototypes really need to hit the mark before pulling the trigger. [Bob's] still hard at work getting his scoreboard off the ground and his most recent endeavor was to find a way to prototype the rubber gasket without blowing his shoes...
The camera attachment can be seen attached to the right lens of the scope. It’s an old security camera which he already had on hand. The stock lens wasn’t going to bring the picture into focus, but he had some different optics on hand and one of them fit the bill perfectly. The rest o...
[Debraj] wrote in about his 2-wire serial backpack he developed for a Graphic LCD screen . It’s build on a hunk of protoboard and uses a pair of 595 shift registers to translate incoming serial data to the parallel interface which is used by the LCD screen. It takes more time to push ...
This component is a one-shot thermal fuse. When the body rises above the specified temperature the two leads stop conducting. They’re useful in applications like motors, where you want to make sure power is cut to an overheating piece of hardware before permanent damage happens. They’...
There’s some really cool stuff to find if you wander around a Michaels craft shop or Hobby Lobby long enough. Recently, [Ben] picked up a craft cutter – a small vinyl cutter-like device meant for scrapbooking and other crafty endevours. He’s using this machine to create solder paste s...
Centuries ago, craftsmen and smiths of all sort spent hundreds of hours crafting a crossbow. From the fine craftsmanship that went into making the bow to the impeccable smithing a windlass requires, a lot of effort went into building a machine of war. Since [Chris] has a 3D printer, h...
[Todd Harrison] wrote in not with a project but with a video tour of his local hackerspace: HeatSync Labs in Mesa, Arizona. He took a camera along with him over the weekend to record what you can expect when visiting the space. You’ll find the tour embedded after the break. It starts ...
